(PDF) Utilizing high volumes quarry wastes in the …
Quarry dust was used to replace sand at ratios of 75% and , and four different water-to-cement ratios (w/c) of 0.52, 0.54, 0.56 and 0.58 were studied and compared. ... 3 Density stability ...
Comparison of physical and mechanical properties of …
The corresponding values for quarry dust are 0.8 and 5.45, respectively. A well-graded soil has a C u value of 5 or more and a C c value between 1 and 3 [25]. The values indicate that the ... The Fig. 2 shows the density results of river sand concrete and quarry dust concrete. The bulk density of normal weight concrete usually ranges from 2200 ...
EFFECT OF QUARRY DUST AS PARTIAL REPLACEMENT OF SAND IN CONCRETE
The loose and compacted bulk density values of. sand were 1455 kg/M3 and 1726 kg/M3 respectively. T able2. Physical properties of fine aggregate. ... Peak value of stone quarry dust is obtained at ...
CALCULATING VOLUMES AND WEIGHTS IN …
BULK DENSITY This is a concept slightly different from the Bulking Factor CONCEPT. ... BULK DENSITIES OF QUARRY PRODUCTS ANDLANDSCAPE MATERIALS (Rev 1 August 2004,Rev 2 2009, Rev 3 2010, Rev 4 2011, Rev 5 2016 Rev6 Sept 2017, REV 7 2018, Rev ... Crusher Dust 1.50 2.20 Sydney (plastering) Sand *1.50 *1.70
AN EXPERIMENTIAL STUDY ON USE OF QUARRY DUST …
1.2 Applications of Quarry Dust:- 1. Quarry dust has a lot of applications in construction and infrastructure sector: 2. Quarry dust is used as a fine aggregate in bituminous mixes, i.e., Dense Bituminous Macadam (DBM), Bituminous Macadam (BM), Bituminous Concrete (BC), etc. 3. Quarry Dust is also used as a base and sub-base layer
Effect of Quarry Dust on Compaction Characteristics of Clay
Variation in the maximum dry density (MDD) and optimum moisture content (OMC) values has been obtained with increasing content and use of different gradations of quarry dust in the two clay types.
Comparison of physical and mechanical properties of …
The corresponding values for quarry dust are 0.8 and 5.45, respectively. ... The Fig. 2 shows the density results of river sand concrete and quarry dust concrete. The bulk density of normal weight ...
EXPERIMENTAL STUDY ON REPLACEMENT OF FINE AGGREGATE BY QUARRY DUST …
• Bulk density of Quarry Dust (IS 2386) 1774.36 kg/m 3 ... The maximum compressive strength values were reached at 20% quarry dust content at the age of 28 days for the three concrete grades ...
Soil bulk density of quarry and non-quarry areas
Mining of stone is important because crushed stone is a construction material for building houses, roads and pavements (Adeyi et al. 2019). However, crushed stone mining has been reported to have ...
Compaction Characteristics of Red Earth and Quarry Dust Combinations
The optimum values of the mixes are defined with respect to the dry density of quarry dust alone. It is observed that there was an increase of 11.61% in the dry density when 40% of the red earth is replaced with quarry dust. The optimum value of quarry dust to be mixed with red earth so as to have maximum shear strength is also …
Quarry dust as river sand replacement in cement masonry …
In the present study, Ordinary Portland Cement which is of bulk density and specific gravity of 1182 kg/m 3 and 3.15, respectively, was deployed as binder. For fine aggregates, river sand, quarry dust and combination of both were used.
(PDF) Thermal Conductivity Performance of Kenaf Core
The density of the quarry dust is . 1,800 kg/m 3. ... reduced the thermal conductivity value and might improve . ... bricks is mainly related to bulk density and porosity.
COMPARATIVE PERFORMANCE ANALYSIS OF FIRED CLAY BRICKS AND QUARRY DUST
The values of the bulk density of the sand a nd ... The quarry dust sandcrete brick produced was compared with the fired clay brick produced in local markets based on compressive strengths and ...
Structural Properties of Laterite -Quarry Dust Cement Blocks
Ec =1.7ρ2 fc 0.33 *10-6 (1) Where Ec = Static modulus of Elasticity, ρ = density, fc = compressive strength Table 4: Result of Static Modulus of elasticity Sample Quarry dust: laterite Average Density (Kg/m3) Compressive Strength (N/mm2) 1 100:0 1976.00 2.03 8.3848 2 90:10 1832.06 2.50 8.8566 3 75:25 1961.82 2.54 8.8676 4 70:30 1894.41 2.56 …
Replacement of River Sand with Quarry Dust in …
Maximum dry density values of the quarry dusts ranged from 2.00 to 2.15g/m3 with an average of 2.11g/m .3 ... quarry dust possess higher relative bulk density and fine
Study on Performance of Quarry Dust as Fine Aggregate in Concrete
After obtaining the max value of stone quarry dust at 10% it is replaced with various percentages of polypropylene fiber (0%, 0.1%, 0.2% and 0.3%). ... specific gravity, and bulk density, and ...
bulk density of quarry li ne
Contribute to dinglei2022/en development by creating an account on GitHub.
Bulk Density Characteristics of Grain Dust
dust at moisture contents ranging from 9 to 15 percent and at pressures ranging from 0 to 120 kPa were determined, where an equation expressing bulk density of grain dust as a function of pressure was given as (Chang and Martin, 1983): p = fi(P) - A^ - A2 Exp(-A3P) + A4P [1] bulk density, kg/m^ pressure, kPa where P = P =
Specific gravity of quarry dust | Download Scientific Diagram
The bulk densities of the river sand, quarry dust and granite are similar to values reported in previous investigations [9, 28]. Fineness modulus obtained for the fine aggregates indicate that ...
Densities of common Products
Always double check the values with other sources before important calculations. Densities common Products; Material Density (lbs/ft 3) ... dust: 68: Linseed oil: 58: Linseed, kernel: 25: Maize, kernel: 45: Malt sugar: 30 - 35: ... Calculate density of a slurry. Soil and Rock - Bulk Factors Soil and rock expansion - or swell - after mining.
Replacement of River Sand with Quarry Dust in …
density values of quarry dust in India ranged from 2.10 . to 2.45 gm/cc (Chandana et al., 2013). ... such as water absorption, specific gravity, and bulk density, and mechanical properties, ...
Sustainability | Free Full-Text | A Study on Mechanical
The concrete mixtures—MIX3 (15% fly ash and 10% aluminum dross) and MIX7 (15% fly ash, 10% aluminum dross, and 20% quarry dust) have recorded an …
Review on Performance of Quarry Dust as Fine …
by quarry dust up to 30% found to improve the properties of concrete as reported by that the compressive and flexural strength of concrete with quarry dust were nearly 40% more than the control concrete. Mir and Shubhada,. Investigated the Quarry dust has also utilisation in other areas of application. Quarry dust with
Quarry dust as river sand replacement in cement masonry …
Section snippets Materials used. In the present study, Ordinary Portland Cement which is of bulk density and specific gravity of 1182 kg/m 3 and 3.15, respectively, was deployed as binder. For fine aggregates, river sand, quarry dust and combination of both were used.
(PDF) Utilization of Quarry Dust and Sludge in Sandcrete …
Bulk density of sludge is 1270Kg/m3 while its specific gravity is 1.55. Table-5: Test result of water treatment sludge Bulk density of hardened hollow blocks The results of the bulk densities for the hardened blocks are shown in Fig 2. Mix label A1 had the highest bulk density of 2049.59Kg/m3 and the lowest value of 1912.46Kg/m3 was from …
IJERT-Study on Strength of Concrete using Lateritic Sand and Quarry …
The results of different are shown in table 4. Table 4: Properties of lateritic sand quarry dust Grading of lateritic sand and quarry dust Properties Specific gravity Bulk density in kg/m3 Water absorption IJERTV3IS120166 Lateritic sand 2.78 1.66 (compact) 1.49 (loose) 4% Quarry dust 2.60 1.62 (compact) 1.32 (loose) 2% 3.
Characteristic studies on the mechanical properties of …
be 2.3. The loose and compacted bulk density values of sand were 1455 and 1726 kg/m 3 respectively. Quarry dust The basic tests on quarry dust were conducted as per IS-383-1987 and its specific gravity was around 1.95. Wet sieving of quarry dust through a 90 micron sieve was found to be 78% and the
Review on Performance of Quarry Dust as Fine …
A byproduct of the quarrying, crushing, and sieving processes, quarry dust is typically referred to as crushed sand (CS), crushed rock powder (CRP), artificial sand (AS), …
(PDF) Towards Optimising the use of Quarry Dust in
Bulk Density . 1735 kg/m 3. Water absorption . 1.2 % . Moisture Content ... [Show full abstract] all sand replacement levels and that concrete with quarry dust had the maximum strain values ...
(PDF) Comparison of physical and mechanical properties …
The respective values obtained for quarry dust concrete in [13], [15] ... These results align with the reported range of bulk density (2200-2400 kg/m 3 ) by Opara et al. [60]. However, both ...